ClareControls CH-THSTAT-W Guia do Utilizador Página 1

Clare Controls IP Network Cameras User Guide Doc ID 2014-12-343 • Rev 04

2 Clare Controls IP Network Camera User Guide Safety warnings and cautions Please pay attention to the following warnings and cautions. Hazardous vo

Clare Controls IP Network Camera User Guide 3 Perchlorate material: Special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate. This

4 Clare Controls IP Network Camera User Guide Cautions  Before using the camera, make sure the power supply voltage is correct.  Do not drop or

Clare Controls IP Network Camera User Guide 5 Network connection If you want to set the network camera via a LAN (Local Area Network), refer to “Set

6 Clare Controls IP Network Camera User Guide Detecting and changing the IP address You need the IP address to visit the network camera. To detect a

Clare Controls IP Network Camera User Guide 7 Setting the network camera over a WAN This section explains how to connect the network camera to a WAN

8 Clare Controls IP Network Camera User Guide Dynamic IP connection Apply a dynamic IP from an ISP. With the dynamic IP address, you can connect the

Clare Controls IP Network Camera User Guide 9 Figure 7: Normal domain name resolution Steps: 1. Obtain and apply a domain name from a domain name

10 Clare Controls IP Network Camera User Guide Access to the network camera Accessing by web browsers Accessing the network camera through a web bro

Clare Controls IP Network Camera User Guide 11 4. Install the plug-in, if prompted, and follow the installation prompts before viewing the live vid

12 Clare Controls IP Network Camera User Guide 7. Click Finish. Note: You may need to close the web browser to install the plug-in. After installi

Clare Controls IP Network Camera User Guide 13 Wi-Fi settings You do not need to use cables when connecting to the wireless network. Note: This cha

14 Clare Controls IP Network Camera User Guide Wireless connection in ad-hoc mode If you choose the Ad-Hoc mode, you do not need to connect the wire

Clare Controls IP Network Camera User Guide 15 Security mode Figure 9: Security Mode Options You select the Security Mode; not-encrypted, WEP, WPA

16 Clare Controls IP Network Camera User Guide WPA-personal and WPA2-personal mode: Enter the required pre-shared key for the access point, a hexad

Clare Controls IP Network Camera User Guide 17 EAP-TLS  Identity - Enter the user ID to present to the network.  Private key password – Enter th

18 Clare Controls IP Network Camera User Guide PBC mode: PBC (Push-Button-Configuration) allows the user to push a button, on both the Access Point

Clare Controls IP Network Camera User Guide 19 2. Select Use router Pin code. 3. If the PIN is generated from the router, enter the PIN in the Ro

20 Clare Controls IP Network Camera User Guide IP property settings for wireless network connection The default IP address of the wireless network i

Clare Controls IP Network Camera User Guide 21 Live View Live View page The live video page lets you view live video, capture images, utilize PTZ co

Copyright © 29DEC14 Clare Controls, Inc. All rights reserved. This document may not be copied in whole or in part or otherwise reproduced without pr

22 Clare Controls IP Network Camera User Guide Starting live view Click on the toolbar to start the live view of the camera. Figure 15: Live View

Clare Controls IP Network Camera User Guide 23 Operating PTZ control In the live view interface, use the PTZ control buttons to realize pan/tilt/zoo

24 Clare Controls IP Network Camera User Guide Setting/calling a preset Setting a preset allows you to switch the camera to a preset position, witho

Clare Controls IP Network Camera User Guide 25 Configuring Live View parameters You can select the stream type and change the image size on the live

26 Clare Controls IP Network Camera User Guide Network camera configuration Configuring local parameters The local configuration refers to the param

Clare Controls IP Network Camera User Guide 27  Record File settings: Set the saving path of the recorded video files. Valid for the record files

28 Clare Controls IP Network Camera User Guide 2. Select the Time Zone. 3. Select the checkbox to enable the NTP function. 4. Configure the follo

Clare Controls IP Network Camera User Guide 29 Configuring TCP/IP settings Configure the TCP/IP settings to operate the camera over the network. The

30 Clare Controls IP Network Camera User Guide Configuring port settings You can set the port numbers of the camera, e.g., HTTP port, RTSP port, and

Clare Controls IP Network Camera User Guide 31 2. Select the Enable PPPoE checkbox to enable this feature. 3. Enter User Name, Password, and Confi

Disclaimer statement “Underwriters Laboratories Inc. (“UL”) has not tested the performance or reliability of the security or signaling aspects of this

32 Clare Controls IP Network Camera User Guide To configure IP server: 1. Enter the Server Address of the IP Server. 2. Click Save. Note: For the

Clare Controls IP Network Camera User Guide 33 Configuring SNMP settings You can set the SNMP function to get the camera status, parameters, alarm-r

34 Clare Controls IP Network Camera User Guide 2. Select the corresponding version checkbox to enable the feature. , , 3. Configure the SNMP s

Clare Controls IP Network Camera User Guide 35 Configuring QoS settings QoS (Quality of Service) can help solve network delay and congestion by conf

36 Clare Controls IP Network Camera User Guide 2. Enter the user name and password required for logging into the FTP server in the corresponding f

Clare Controls IP Network Camera User Guide 37 2. Select the Enable UPnP checkbox. This enables the Friendly Name field. 3. In the Friendly Name f

38 Clare Controls IP Network Camera User Guide 2. In the Stream Type field, select Main Stream (normal), Sub-Stream, or Third Stream. Note: Main S

Clare Controls IP Network Camera User Guide 39 Profile: Basic profile, Main Profile, and High Profile are selectable for coding. I Frame interval: S

40 Clare Controls IP Network Camera User Guide Configuring ROI encoding ROI stands for the region of interest. ROI encoding lets you discriminate th

Clare Controls IP Network Camera User Guide 41 Overexposure prevention: Enable or disable the function in this field. Exposure time: Value range

Clare Controls IP Network Camera User Guide i Content Important information...1 Limitation of liability...1 Safety warnings and cautions...2 Adviso

42 Clare Controls IP Network Camera User Guide BLC area: BLC area is the sense of the light intensity; Close, Up, Down, Left, Right, and Center are

Clare Controls IP Network Camera User Guide 43 Configuring OSD Settings You can customize the camera name and time displayed on the screen. To confi

44 Clare Controls IP Network Camera User Guide Configuring text overlay settings You can customize the text overlay. To configure text overlay setti

Clare Controls IP Network Camera User Guide 45 Configuring privacy mask Privacy mask lets you cover certain areas on the live video to prevent zones

46 Clare Controls IP Network Camera User Guide Configuring picture overlay Picture overlay lets you overlay a picture on the image. To configure pi

Clare Controls IP Network Camera User Guide 47 Configuring and handling alarms This section explains the configuration of the network camera to resp

48 Clare Controls IP Network Camera User Guide Arming schedule for motion detection You can set the arming schedule for motion detection. Figure 16:

Clare Controls IP Network Camera User Guide 49 Set the alarm actions for motion detection. You can specify the linkage method when an event occurs.

50 Clare Controls IP Network Camera User Guide 2. Select the Enable Video Tampering checkbox to enable the tamper-proof detection. 3. Set the tam

Clare Controls IP Network Camera User Guide 51 Email sending triggered by alarm The system can be configured to send an Email notification to all de

ii Clare Controls IP Network Camera User Guide Network camera configuration...26 Configuring local parameters...26 Configuring time settings...27 C

52 Clare Controls IP Network Camera User Guide Attached image: Select the checkbox Attached Image if you want to send the emails with attached alarm

Clare Controls IP Network Camera User Guide 53 To upload event-triggered snapshots to FTP: 1. Configure the FTP settings and select the Upload Pict

54 Clare Controls IP Network Camera User Guide Arming or disarming the camera This section if for supported cameras only. Follow the steps below to

Clare Controls IP Network Camera User Guide 55 Configuring PTZ This section explains the PTZ functions of the network camera. This enables the pan/t

56 Clare Controls IP Network Camera User Guide Auto Scene Speed: Select an option 1 through 40. Max. Tilt-angle: Select either -5 to 90, -4 to 90,

Clare Controls IP Network Camera User Guide 57 2. Select the Enable Limit checkbox to enable this function 3. Select from the Limit Type drop-down

58 Clare Controls IP Network Camera User Guide Configuring the PTZ park action The Park Actions lets you stop the camera. To configure the park acti

Clare Controls IP Network Camera User Guide 59 2. Select the Enable Privacy Mask checkbox to enable this function. 3. Click Draw Area. 4. Click

60 Clare Controls IP Network Camera User Guide 2. Set a second amount in the Park Time field. 3. Click Edit Tasks to change the day, task type,

Clare Controls IP Network Camera User Guide 61 Clearing a PTZ configuration The Clear Configuration settings lets you clear other settings individua

Clare Controls IP Network Camera User Guide iii Storage settings...62 Configuring NAS settings...62 Configuring recording schedule...63 Playback...

62 Clare Controls IP Network Camera User Guide Storage settings To configure record settings, make sure that you have a network storage device in th

Clare Controls IP Network Camera User Guide 63 2. If the status of the disk is uninitialized, select the corresponding checkbox to select the disk,

64 Clare Controls IP Network Camera User Guide 2. Select the Enable Record Schedule checkbox to enable scheduled recording. 3. Set the recording

Clare Controls IP Network Camera User Guide 65 Choose the day to set the record schedule. Set all-day record or segment record: 1. If you want to

66 Clare Controls IP Network Camera User Guide Record Triggered by Motion & Alarm: If you select Motion and Alarm, the video will be recorded wh

Clare Controls IP Network Camera User Guide 67 Playback View the recorded video files stored in the network disks or SD cards. To configure playback

68 Clare Controls IP Network Camera User Guide Table 3: Description of the Playback toolbar Icon Operation Play Pause Stop Speed down Speed up

Clare Controls IP Network Camera User Guide 69 Log searching The operation, alarm, exception, and information of the camera can be stored in log fil

70 Clare Controls IP Network Camera User Guide Others Understanding camera capacity in an NVR When setting up your NVR and cameras, you may notice t

Clare Controls IP Network Camera User Guide 71 Generally, 5 MP at 30 fps requires around 20 Mbps for best quality. A 4-channel NVR is currently limi

iv Clare Controls IP Network Camera User Guide

72 Clare Controls IP Network Camera User Guide To modify a user: 1. Click to select the user from the list and click Modify. 2. Modify the User

Clare Controls IP Network Camera User Guide 73 Configuring RTSP authentication You can specifically secure the stream data of live view. To confi

74 Clare Controls IP Network Camera User Guide 2. Set the Anonymous Visit permission in the drop-down list to enable or disable the anonymous visit

Clare Controls IP Network Camera User Guide 75 4. Select either Forbidden or Allowed. 5. Set the IP Address Filter list. To add an IP address: 1.

76 Clare Controls IP Network Camera User Guide Viewing device information Enter the Device Information interface. Configuration > Camera Configur

Clare Controls IP Network Camera User Guide 77 Restoring default settings To restore default settings: 1. Enter the Maintenance interface. Configu

78 Clare Controls IP Network Camera User Guide 2. Click Browse to select the local configuration file, and then click Import to start importing the

Clare Controls IP Network Camera User Guide 79 Note: If you want to connect the camera by the RS-232 port, the parameters of the RS-232 must match

80 Clare Controls IP Network Camera User Guide Appendix 1 SADP software introduction Description of SADP V 2.0 SADP (Search Active Devices Protocol)

Clare Controls IP Network Camera User Guide 81 Search online devices manually Click Refresh to refresh the online device list manually. The new devi

Clare Controls IP Network Camera User Guide 1 Important information Limitation of liability To the maximum extent permitted by applicable law, in no

82 Clare Controls IP Network Camera User Guide Appendix 2 Port mapping The following settings are for a TP-LINK router (TL-R410). The settings vary

Clare Controls IP Network Camera User Guide 83 As the settings mentioned above, map the port 80, 8000, 554 and 8200 for the network camera at 192.16